Laredo Elite Epoxy Flooring provides professional flake & chip epoxy systems in Laredo, TX for residential and commercial properties across the South Texas border region. Flake and chip epoxy is the most popular floor we install in Laredo, and the reason is unglamorous: it hides things.
A broadcast of vinyl chips scattered into a wet 100% solids base coat breaks up the surface visually, which means old patch lines, trowel swirls, saw-cut joints and the general unevenness of a slab poured in 1994 stop being the first thing your eye lands on.
Flake floors also read as intentional rather than industrial, which matters in a garage that doubles as a workshop or a gym. There are two builds and the difference is real.
A partial broadcast throws chips at maybe half coverage, leaves base color showing between them, and costs less.
A full broadcast means the installer keeps throwing flake until the floor will not absorb another chip, which is what "broadcast to refusal" means, and then the next day scrapes the standing flake back flat and vacuums it off before the clear coats go down.
Full broadcast is what you want. It gives a consistent texture across the whole floor, it gives genuine slip resistance because the scraped chip edges create profile, and it makes future touch-ups blend instead of announcing themselves.
Chip sizes run from 1/16 inch, which reads almost like terrazzo, up to 1/4 inch, which reads bold and chunky.
Blends are mixed to a color recipe, so we can pull a floor toward warm tans that live well with Laredo caliche dust and Saltillo tile, or push it gray and cool for a shop.
Build sequence, start to finish: diamond grind to CSP 2 to 3, repair spalls, fill control joints with a semi-rigid polyurea so the joint can still move, moisture-mitigating primer if the slab warrants it, roll the pigmented 100% solids base at roughly ten mils, broadcast flake to refusal while the base is still open, cure overnight, scrape and vacuum, then two coats of polyaspartic clear.
Total thickness lands around thirty to forty mils, which is roughly ten times a rolled-on garage paint.
In commercial work around Laredo the same system goes into showroom restrooms, dealership service write-up lanes, breakrooms in warehouses off Killam Industrial Boulevard, and pharmacy and clinic floors that want a cleanable surface without a hospital look.
One caution worth saying out loud: a flake floor with a gloss clear is beautiful and it is slick when it is wet unless anti-slip aggregate is added to the final coat.
We add it by default in any area that gets hosed, gets rain tracked in, or gets a cooler dragged across it. If somebody quotes you a flake floor and does not mention traction, that is a tell.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — 100% solids epoxy, diamond grinding and shot blasting equipment, ICRI concrete surface profile gauges, ASTM F1869 calcium chloride test kits, ASTM F2170 in-situ relative humidity probes, moisture-mitigating epoxy primers — and backs the work with a written workmanship warranty. We serve Laredo and nearby communities including Rio Bravo, El Cenizo, Zapata, San Ygnacio.
What We Handle
Everything our flake & chip epoxy systems in Laredo covers
One crew, one point of contact, and the full range of flake & chip epoxy systems work in Laredo, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- flake epoxy floor Laredo
- chip epoxy flooring
- vinyl flake garage floor
- full flake broadcast system
- decorative chip floor
- flake floor colors
- epoxy flake vs solid color
- flake and polyaspartic system
- commercial flake flooring
- flake floor cost per square foot
- partial broadcast flake
- quarter inch flake floor
- epoxy floor coating with flakes
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Laredo services.
Materials, equipment and how we do flake & chip epoxy systems
The difference between flake & chip epoxy systems that lasts and flake & chip epoxy systems that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with 100% solids epoxy, diamond grinding and shot blasting equipment, ICRI concrete surface profile gauges, ASTM F1869 calcium chloride test kits, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Laredo job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of epoxy flooring work in the South Texas border region means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do flake & chip epoxy systems outside Laredo
Laredo Elite Epoxy Flooring covers Laredo and the surrounding communities of the South Texas border region. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Flake & Chip Epoxy Systems in Rio Bravo, TX — Webb County, incorporated in 1989, population 4,450 at the 2020 census
- Flake & Chip Epoxy Systems in El Cenizo, TX — Webb County, incorporated in 1989, population 2,540 at the 2020 census
- Flake & Chip Epoxy Systems in Zapata, TX — Zapata County, county seat, population 5,383 at the 2020 census
- Flake & Chip Epoxy Systems in San Ygnacio, TX — Zapata County, founded in 1830, population 504 at the 2020 census
- Flake & Chip Epoxy Systems in Bruni, TX — Webb County, established in 1877, population 251 at the 2020 census
- Flake & Chip Epoxy Systems in Mirando City, TX — Webb County, established in 1921, population 222 at the 2020 census
Start on the Laredo Elite Epoxy Flooring homepage for a free estimate, or call (855) 620-6087 and describe the job.
Why Laredo Chooses Laredo Elite Epoxy Flooring
- ✓Over 15 years of warehouse, truck shop and garage floor work across Webb County
- ✓Slab moisture tested to ASTM F1869 and ASTM F2170 before we quote, not after a failure
- ✓Diamond grinding and shot blasting to a measured ICRI profile, never an acid etch
- ✓Semi-rigid polyurea joint filling so hard-wheel traffic stops eating your control joints
The standards behind flake & chip epoxy systems
Quality here is not a matter of opinion — it is written down. The flake & chip epoxy systems work we do in Laredo follows published industry standards: ASTM International publishes ASTM F1869 and F2170, the slab moisture tests a coating depends on, and American Concrete Institute sets the surface-profile and substrate requirements. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every flake & chip epoxy systems project in Laredo gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (855) 620-6087 for a free flake & chip epoxy systems free estimate in Laredo, or request a quote and we'll get right back to you.