A full flake epoxy floor is chips broadcast into wet resin until the surface physically will not take another one — and it's the best-value garage floor most people can buy. It hides dirt, hides slab imperfections, grips better than any smooth coating, costs $4 to $8 a square foot, and it's the one system that still looks fine after your teenager drops a wrench on it.
Also, and we say this with affection, the loose flake will find its way into your house. Every installer's truck has vinyl chips in the carpet. It's the trade's version of glitter.
Full broadcast vs light scatter
This is the distinction that actually changes your quote, and it's the one that gets blurred in bids.
Full broadcast (to refusal). The installer throws chip into the wet base coat continuously until the resin won't accept more. You end up with a floor that's essentially 100 percent chip coverage. The next day the crew scrapes the sharp standing edges down and vacuums off everything loose, then applies clear topcoats over the top.
Light or partial scatter. A deliberate, lighter throw that lets the pigmented base coat show through between chips. Uses about a third of the material, skips or shortens the scrape day, and reads as cleaner and more modern.
| Full broadcast | Partial scatter | |
|---|---|---|
| Chip material used | 2–3x more | Baseline |
| Hides dirt and slab flaws | Excellent | Moderate |
| Texture underfoot | Slightly grippy | Nearly smooth |
| Total system thickness | Thicker | Thinner |
| Look | Terrazzo, busy, forgiving | Clean, base color visible |
| Cost | $5–$8 / sq ft | $4–$6 / sq ft |
| Best for | Working garages, shops | Basements, showrooms, modern builds |
For a garage that parks cars and holds the lawnmower, full broadcast is the right answer nearly every time. The forgiveness is the feature.
Chip size, color, and the choice people overthink
Chip comes in 1/8, 1/4, 1/2, and 1 inch. Quarter-inch is the residential default and gives a fine, natural speckle. Eighth-inch reads almost as a solid color from standing height. Half-inch and larger give a bold terrazzo look that suits big commercial spaces and looks slightly frantic in a one-car garage.
Color blends are usually named things like Domino, Tuxedo, Coffee, Shale. Here's the practical advice nobody offers at the sample table: pick a blend with some mid-gray and some dark in it. All-light blends show every tire mark. All-dark blends show dust. Mixed blends hide both, which is the entire reason flake exists.
Look at samples in daylight, not under the shop's fluorescents, and look at a full-size sample board rather than a two-inch chip card. The pattern changes character at scale.
What a real flake install looks like, day by day
Day 1 — prep. Diamond grinding with metal-bond then resin-bond segments to an ICRI CSP 2 to 3 profile. Moisture testing per ASTM F1869 (calcium chloride, 3 pounds per 1,000 sq ft per 24 hours as the usual ceiling) or ASTM F2170 (in-situ RH probes at 75 to 80 percent). Crack chasing, joint treatment, oil dig-outs, and grinding the perimeter and corners by hand.
Day 1 or 2 — base and broadcast. A pigmented 100 percent solids epoxy base coat goes down at roughly 10 to 15 mils, and the chip goes in immediately while it's wet. This part looks like someone is angrily seeding a lawn.
Day 2 or 3 — scrape, vacuum, topcoat. Loose and standing chip comes off. Then one or two clear coats. If it's polyaspartic, foot traffic in 4 to 8 hours and vehicles in about 24. If it's epoxy or urethane clear, foot traffic in 24 to 48 hours and vehicles at 5 to 7 days.
Total: two to three days on site for most residential garages, with the vehicle wait being the part that actually affects your life.
The two things that decide whether it lasts
The grind. Not the brand of resin, not the chip, not the color. Acid etching produces a fraction of the mechanical profile that diamond grinding does, and it's the single most common reason coated floors fail. A properly bonded system fails in the concrete when pull-tested per ASTM D4541, not at the bond line.
The moisture test. A slab on grade with no vapor barrier under it can push a coating off from below no matter how well it was ground. If a bid doesn't mention testing, ask. The mitigation primer costs $1 to $2.50 a square foot and is dramatically cheaper than doing the floor twice. More on how these floors fail in why epoxy floors peel.
Our one strong opinion about flake
Full flake with a polyaspartic topcoat is the best price-to-performance garage floor available, and metallic is a worse choice for a working garage no matter how good it looks online.
Here's the reasoning with a number attached. Flake at $5 to $6 a foot hides scratches, hides tire scuffs, hides the patch where the old coating was, and can be spot-repaired by grinding a small area and re-broadcasting. Metallic at $9 to $12 shows every scratch because it's a continuous reflective surface, and it can't be patched at all because the swirl pattern is made in one continuous pour.
You'd be paying roughly 70 percent more for a floor that's harder to live with. If you want the showpiece and the car mostly sits on a lift, absolutely go metallic — we cover that in metallic epoxy floor cost. For a garage that gets used, flake wins on the merits.
When you should do it yourself
Honestly: if the space is a shed, a detached shop, a storage bay, or a basement where no car parks, buy a good 100 percent solids kit and rent a grinder for about $100 a day. Roughly $400 to $600 all in, and you'll get 5 to 8 solid years. Broadcasting flake by hand is genuinely satisfying and very hard to do badly, because the chip hides your technique. That's the whole point of chip.
Two things will sink a DIY flake floor, and neither is the flake: skipping the mechanical grind, and coating a slab that's pushing moisture. Rent the grinder. Tape a two-foot square of plastic sheeting to the slab overnight per ASTM D4263 and see if it's damp underneath in the morning. That's a free test and it'll tell you whether to call someone.
Bottom line
Full broadcast for working garages, partial for finished spaces. Quarter-inch chip, a mixed-tone blend, and a polyaspartic clear over the top. Then spend your attention on the grind and the moisture test, because those decide whether any of the rest matters.
Laredo Elite Epoxy Flooring installs full flake epoxy systems, garage floor coatings, and polyaspartic topcoats across Laredo and the South Texas border region. We'll bring full-size sample boards, moisture test before we quote, and tell you honestly if a kit would serve you better. Call (844) 511-2320.
Ready for a free quote in Laredo?
Laredo Elite Epoxy Flooring — free estimate, clear scope, no pressure. Use the form on this page or jump to the homepage quote.
Related services in Laredo
Laredo Elite Epoxy Flooring money pages — go straight to the service you need.
- Garage Floor Coatings →
A garage floor epoxy system turns the dustiest slab in a Laredo house into the easiest surface in it to clean. Bare concrete here does three things badly: it sheds a fine grey powder that tracks into the house, it drinks every drop of oil that leaves your truck, and it stains permanently from the caliche dust that blows off every unpaved lot in Webb County.
- Flake & Chip Epoxy Systems →
Flake and chip epoxy is the most popular floor we install in Laredo, and the reason is unglamorous: it hides things. A broadcast of vinyl chips scattered into a wet 100% solids base coat breaks up the surface visually, which means old patch lines, trowel swirls, saw-cut joints and the general unevenness of a slab poured in 1994 stop being the first thing your eye lands on.
- Polyaspartic Coatings →
Polyaspartic coatings are what make a one-day floor possible and what keep a floor from turning yellow in Laredo sun. Chemically they are an aliphatic polyurea, which is a mouthful that matters for one reason: the aliphatic backbone is UV stable, so the coating holds its color and gloss where a standard epoxy clear ambers within a year or two of daylight exposure.
- Quartz Broadcast Systems →
A quartz broadcast floor is what you specify when you need real slip resistance and real durability and the floor still has to look like something a customer can see. Colored quartz aggregate, which is kiln-fired ceramic-coated silica rather than plain sand, is broadcast into a wet epoxy base until the surface will not take any more, then locked down with grout and topcoats.
- Metallic Epoxy Floors →
Metallic epoxy is the floor people photograph. Fine metallic pigment is dispersed into a clear 100% solids epoxy, poured, and then moved with a squeegee, a roller, a brush and sometimes a heat gun until the pigment separates into veins, cells and pearl-like drifts that read as marble or poured stone.
Frequently asked questions
What does full flake mean on a garage floor?
Full flake means the installer broadcasts vinyl chips into the wet base coat until the surface will not accept another one, which is called broadcasting to refusal. The next day the excess is scraped and vacuumed off, then sealed with one or two clear topcoats. A light or partial broadcast uses roughly a third of the chip and lets base color show through.
How much does a full flake epoxy floor cost?
Roughly $4 to $8 per square foot installed, so about $1,800 to $3,600 for a typical 450 square foot two-car garage. Full broadcast sits at the higher end because it uses two to three times the chip material and adds a scrape-and-vacuum day to the schedule.
Is full flake better than partial flake?
Full broadcast hides dirt and imperfections better, feels slightly textured underfoot, and builds a thicker overall system. Partial flake costs less and gives a cleaner, more modern look with visible base color. For a working garage, full broadcast is the better buy. For a finished basement or a showroom, partial often looks better.
What size flake should I use?
Quarter-inch chip is the residential standard and reads as a fine speckle. Eighth-inch is subtler and closer to a solid color from standing height. Half-inch and one-inch chips give a bold terrazzo look and are common in commercial spaces. Bigger chips build more texture, which grips better and takes marginally more effort to sweep.
Is a flake floor slippery?
Less than solid color or metallic, because the chip edges break up the surface. It's still a coated floor, so wet is wet. If the garage sees snowmelt, rain blowing in, or hose-downs, ask for aluminum oxide or polymer grit in the topcoat on top of the flake texture.
How long does a flake epoxy garage floor last?
Ten to twenty years in residential use when the slab was diamond ground, moisture tested, and topcoated properly. The chip layer is essentially permanent. What wears is the clear topcoat, which can be scuffed, screened, and recoated at around year eight to twelve for a fraction of a new install.
Can you install flake epoxy over an old coating?
Only if the old coating is genuinely well bonded, and it still has to be ground to profile. Score a small square and pull duct tape off it. If the old coating lifts, it comes off entirely first. Broadcasting new chip over a failing coating buys you about a year of looking good.
Local context
How this applies in Laredo, TX
Every article here is written from epoxy flooring work done in Laredo and the South Texas border region, so the numbers reflect local labour, permit and material costs rather than a national average. Your own job can land either side of them depending on access, the condition of what is already there, and the materials you pick — 100% solids epoxy, diamond grinding and shot blasting equipment, ICRI concrete surface profile gauges.
The way to turn any of this into a real answer is to have someone look at your actual situation. The free estimate is free, itemized and written down, with no deposit and no obligation. Call (844) 511-2320 or start on the Laredo Elite Epoxy Flooring homepage.
Areas Laredo Elite Epoxy Flooring covers
Laredo first, then the surrounding communities of the South Texas border region. Each has its own page with local detail rather than a copy of this one:
- Rio Bravo, TX — Webb County, incorporated in 1989, population 4,450 at the 2020 census
- El Cenizo, TX — Webb County, incorporated in 1989, population 2,540 at the 2020 census
- Zapata, TX — Zapata County, county seat, population 5,383 at the 2020 census
- San Ygnacio, TX — Zapata County, founded in 1830, population 504 at the 2020 census
- Bruni, TX — Webb County, established in 1877, population 251 at the 2020 census
- Mirando City, TX — Webb County, established in 1921, population 222 at the 2020 census
Or jump to the full list of Laredo services.
The Laredo Elite Epoxy Flooring Team
Licensed epoxy flooring pros in Laredo, TX
Written by the Laredo Elite Epoxy Flooring team — licensed, insured epoxy flooring pros with 15+ years serving Laredo, TX and the surrounding area.